耳机插座PJ-6.3耳机座麦克风插座通讯连接器AV插座音频连接�?/h1>

起批量（�?/span>（�/th>	价格
>1000	� 0.60

• 供货总量10000�?/li>
• � � �?/span>广东 深圳
• 联系人：王春霝�/strong>女士(经理)

添加收藏

供应商信�?/p>

王春霝�/a>

主营产品９�/span>
USB系列1394系列2.5耳机插座轻触开兲�/a>3.5耳机插座S端子系列SD卡座MINI卡座HDMI系列电源插座

进入商铺 | >收藏企业

耳机插座PJ-6.3耳机座麦克风插座通讯连接器AV插座音频连接器的详细描述９�/h5>

一．电器性能规格　�?/span>LECTRICAL CHARACTERISTICS
项目Item		测试条件Test Conditions		表现Performonce
接触电阻 Contact Resistance		在微小电�?/span>(100mA )以下测试 Measured at small l current (100mA or less) 1000HZ		30毫欧以下 30m��Min
绝缘电阻 InsulationResistance		输入500V电压1分钟,按以下方式测诔�/span>:Apply a voltage of 250V DC for 1 min to following portions after mhich measurement shall be made: (1)塑胶体与针脚之间(1)Between body and conductor (2)不接触的针脚之间(2)Between conductor not to be contact		100兆欧以上 100m��Min
耐电厊�/span> Dielectric Strength		输入AC500V(50-60HZ)电压,1分钟感应电流丹�/span>0.5MA,按以下方法测诔�/span>: AC 250V ims(50-60HZ) for 1 min trip current: 0.5 mA (1)塑胶体与排脚之间(1)Between terminals (2)不接触的排脚之间: (2)Between individual terminals and frame		没有绝缘破坏等异帷�/span> No damage to parts arcing , orbreakdown etc
使用温度范围 Practical Temperature Range		-25ℂ�/span>----+75ℂ�/span>
测试标准状�?/span> Standard Conditions Atmospheic		在没有指定的情况下测试温�?/span>,湿度,气压如下: Unless otherwise specified , the stardard range or atmospheric conditions for making measurements and tests are as follows (1)温度丹�/span>5ℂ�/span>--35�?nbsp; (1)Ambient temperature:5ℂ�/span>to 35ℂ�/span> (2)湿度丹�/span>45%--85% (2)Relative humidity :45% to 85% (3)气压丹�/span>80KPA----106KPA (3)Air pressure : 80Kpa to 106Kpa
事�/span>.机械性能规格MECHANICAL CHARACTERISTICS
动作劚�/span> Operation Force				250gf��50gf 160gf��20gf
端子强度 Terminal Strength		在排脚前端任意一个方向的先端加上300克力力度测试，时间为15科�/span> A static load of 300gf shall be applied to the tip of the terminal for 15 sec in any direction		在排脚中没有裂开，松动等异常满足于机�?/span>,电器性能:.Electrical characteristics shall be satisfied without damage or escessive looseness of terminals
寿命测试 Life Test		负荷：在负荷的条件下以每分钟25-30回的频率进行100,000次的负荷测试; Aswitch shall be subjected to 100.000 cycles at a speed of 25-30 cycles for 1 min		接触电阻不能超过100毫欧,Contact resistance shall be 100m��Max其他满足于机�?/span>,电器性能Mechanical and electrical characteristics shall be satisfied
	丈�/span>.耐久�?/span> DURABILITY
	项目Item		测试条件Test Conditions	表现Performonce
	可焊性试骋�/span> Solderability Test		温度丹�/span>245��5�?时间�?��0.5科�/span> The solder bath of 255��5ℂ�/span>for 3��0.5 seconds	焊锡部分粘锡均匀,饱满,锡面平滑 Area of soldering need be smooth and good performance
	耐热试验 Heat Test		放置在温�?/span>85��2ℂ�/span>中测诔�/span>96小时名�/span>,再放置常温中1小时来测宙�/span>. The switch shall be stored at a temperature of 85��2ℂ�/span>for96 hours, Then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made	外观无异帷�/span> ,能满足于机械,电器性能 There shall be no defomation or cracks in molded part
	耐冷试验 Cold Test		放置在温�?/span>-20��3ℂ�/span>中测诔�/span>96小时名�/span>,再放置常温中1小时来测宙�/span>. The switch shall be stored at a temperature of -20��3ℂ�/span>for96 hours, Then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made
	潮湿试验 Humidity Test		放置在温�?/span>40��2ℂ�/span>相对湿度丹�/span>90%-96%环境�?/span>96小时名�/span>,再放置常温中1小时来测宙�/span>. The switch shall be stored at a temperature of40��2ℂ�/span>and a humidity of 90%-96% for 96 hours, Then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made